Wells SS-4 Specifications download pdf (Page 2)

Unless otherwise specied, all commercial cooking

equipment manufactured by Wells Manufacturing is

warranted against defects in materials and workmanship

for a period of one year from the date of original installation

or 18 months from the date of shipment from our factory,

whichever comes rst, and is for the benet of the original

purchaser only.

THIS WARRANTY IS THE COMPLETE AND ONLY

WARRANTY, EXPRESSED OR IMPLIED IN LAW

OR IN FACT, INCLUDING BUT NOT LIMITED TO,

WARRANTIES OF MERCHANTABILITY OR FITNESS

FOR ANY PARTICULAR PURPOSE, AND/OR FOR

DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES

IN CONNECTION WITH WELLS BLOOMFIELD

PRODUCTS. This warranty is void if it is determined

that, upon inspection by an authorized service agency,

the equipment has been modied, misused, misapplied,

improperly installed, or damaged in transit or by re,

ood or act of God. It also does not apply if the serial

nameplate has been removed, or if service is performed

by unauthorized personnel. The prices charged by Wells

Manufacturing for its products are based upon the limitations

in this warranty. Seller’s obligation under this warranty

is limited to the repair of defects without charge by a

Wells Manufacturing factory authorized service agency

or one of its sub-service agencies. This service will be

provided on customer’s premises for non-portable models.

Portable models (a device with a cord and plug) must be

taken or shipped to the closest authorized service agency,

transportation charges prepaid, for service. In addition to

restrictions contained in this warranty, specic limitations

are shown in the Service Policy and Procedure Guide.

Wells Manufacturing authorized service agencies are

located in principal cities. This warranty is valid in the United

States and Canada and void elsewhere. Please consult

your classied telephone directory, your foodservice

equipment dealer or contact:

Wells Manufacturing

10 Sunnen Dr., St. Louis MO 63143 USA

phone (314) 678-6314 or fax (314) 781-2714

LIMITED WARRANTY STATEMENT

SERVICE POLICY AND PROCEDURE GUIDE and ADDITIONAL WARRANTY EXCLUSIONS

NOTE: For your protection, please note that equipment

in this shipment was carefully inspected and packaged

by skilled personnel before leaving the factory. Upon

acceptance of this shipment, the transportation company

assumes full responsibility for its safe delivery.

IF SHIPMENT ARRIVES DAMAGED:

1. VISIBLE LOSS OR DAMAGE: Be certain that any

visible loss or damage is noted on the freight bill or

express receipt, and that the note of loss or damage is

signed by the delivery person.

2. FILE CLAIM FOR DAMAGE IMMEDIATELY:

Regardless of the extent of the damage.

3. CONCEALED LOSS OR DAMAGE: if damage is

unnoticed until the merchandise is unpacked, notify the

transportation company or carrier immediately, and

le “CONCEALED DAMAGE” claim with them. This

should be done within fteen (15) days from the date

the delivery was made to you. Be sure to retain the

container for inspection.

Wells Manufacturing cannot assume liability for damage or

loss incurred in transit. We will, however, at your request,

supply you with the necessary documents to support your

claim.

SHIPPING DAMAGE CLAIM PROCEDURE

1. Resetting of safety thermostats, circuit breakers, over

load protectors, and/or fuse replacements are not

covered by this warranty unless warranted conditions

are the cause.

2. All problems due to operation at voltages or phase

other than specied on equipment nameplates are not

covered by this warranty.

Conversion to correct voltage and/or phase must be

the customer’s responsibility.

3. All problems due to electrical connections not made

in accordance with electrical code requirements and

wiring diagrams supplied with the equipment are not

covered by this warranty.

4. Replacement of items subject to normal wear, to

include such items as knobs, light bulbs; and,

normal maintenance functions including adjustments

of thermostats, adjustment of micro switches and

replacement of fuses and indicating lights are not

covered by warranty.

5. Damage to electrical cords and/or plug due to exposure

to excessive heat are not covered by this warranty.

6. Full use, care, and maintenance instructions supplied

with each machine. Noted maintenance and

preventative maintenance items, such as servicing

and cleaning schedules, are customer responsibility.

Those miscellaneous adjustments noted are customer

responsibility. Proper attention to preventative

maintenance and scheduled maintenance procedures

will prolong the life of the appliance.

7. Travel mileage is limited to sixty (60) miles from an

Authorized Service Agency or one of its sub-service

agencies.

8. All labor shall be performed during regular working

hours. Overtime premium will be charged to the buyer.

9. All genuine Wells replacement parts are warranted

for ninety (90) days from date of purchase on non-

warranty equipment. This parts warranty is limited only

to replacement of the defective part(s). Any use of non-

genuine Wells parts completely voids any warranty.

10. Installation, labor, and job check-outs are not

considered warranty and are thus not covered by this

warranty.

11. Charges incurred by delays, waiting time or operating

restrictions that hinder the service technician’s ability

to perform service are not covered by warranty. This

includes institutional and correctional facilities.

2M-308034; Drop-In Round Warmer w/Innite Switch Control

1 2 3 4 5 6 7 ... 15 16

Comments to this Manuals

No comments

Wells SS-4 Specifications Page 2

Comments to this Manuals

Related products and manuals for Food warmers Wells SS-4