Wells HSW-6 User Manual download pdf

MASTER

CONTROL

PANEL

SCREWDRIVER

COUNTERTOP

WELLSLOK

GASKET

WARMER FLANGE

IMPORTANT:

MOUNT APPLIANCE SO THAT THE

CONTROL PANEL IS LOCATED TO

THE FRONT OF THE FIXTURE.

UNIT TO THE NEAREST SURFACE

MINIMUM CLEARANCE REQUIRED FROM

4 1/2

(114)

6 3/4

(171)(51)

(25)

FRONTBOTTOMSIDEBACK

CLEARANCES

INSTALLER MUST MEET CONDITIONS OF ACCEPTABILITY

OUTLINED BELOW UPON INSTALLATION:

1. Required installation clearances:

Wooden and Metal Installation: DO NOT install closer than

4 1/2 inches to front wall, 1 inch to back, 2 inches to

side wall, and 6 3/4 inches to surface below the unit.

2. Unit shall be accessible for servicing from the bottom.

3. If storage is to be used underneath the unit, it is

recommended that a baffle be placed 8 1/2 inches below

the unit to avoid contact with elevated temperatures.

TO FABRICATE:

1. Layout cutout dimensions on countertop and front apron,

shown in cutout details above.

2. Cut and/or drill holes as required in countertop and

apron.

3. Must be accessible for servicing from the bottom.

TO INSTALL:

IMPORTANT - DO NOT disconnect lead wires from the Master

Control Panel when making installation.

1. Locate warmer and control over the counter cutout. Pass

the control box through the opening, then mount the control

box to the rear of the apron.

2. Apply a bead of silicone adhesive/sealant to the gasket

on the underside of the warmer flange, then seat warmer

onto the countertop. Properly position.

3. From underneath, insert screwdriver into "slots" on the

wellslok frame and twist "ears" outward to secure flange

tightly to countertop (see detail).

4. Mount control box to apron cutout as shown in drawing.

5. Mount control panel onto electrical box using the screws

supplied.

PRODUCT DIMENSIONSCUTOUT DETAILS

90°C

90°C14 AWB Cu

14 AWB CuSINGLE

SINGLE6.9

6.9

825

825120

120HSW-6D

HSW-6

RATING

GAUGE

FIELD

TEMP.

WIRINGPHASEAMPSWATTSVOLTSMODEL

ELECTRICAL

WELLS/BLOOMFIELD * VERDI, NV

MODELS HSW-6 (D)

BUILT-IN RECTANGULAR FOOD WARMERS

INSTALLATION INSTRUCTIONS

40740-1 REV (-)

INSTALLATION INSTRUCTIONS

1/2 IN NPT

DRAIN ON

HSW-6D MODEL

TOP CUTOUT FRONT PANEL CUTOUT

9 5/8

(244)

4 1/4

(108)

7 3/16

(183)

12 17/32

(318)

10 11/32

(263)

11 7/8

(302)

11 5/8

(295)

13 7/8

(352)

10 7/8

(276)

13 3/8

(340)

4 7/8

(124)

(127)

4 1/2

(114)

INCHES

(MM)

Summary of Contents

Page 1 - INSTALLATION INSTRUCTIONS

MASTERCONTROLPANELSCREWDRIVERCOUNTERTOPWELLSLOKGASKETWARMER FLANGEIMPORTANT:MOUNT APPLIANCE SO THAT THECONTROL PANEL IS LOCATED TOTHE FRONT OF THE FIX

Wells HSW-6 User Manual

Browse online or download User Manual for Food warmers Wells HSW-6. HSW-6 (D)

Summary of Contents

More documents for Food warmers Wells HSW-6

Comments to this Manuals

Wells HSW-6 User Manual

Browse online or download User Manual for Food warmers Wells HSW-6. HSW-6 (D)

Summary of Contents

More documents for Food warmers Wells HSW-6

Comments to this Manuals

Related products and manuals for Food warmers Wells HSW-6